![]() ![]() The next step of the process is to adjust the board outline. The image is hiding behind the board outline. For the tail, we hold down the “t” key of our keyboard, hold our mouse pointer over the tail of the board on the image and left click our mouse. To line up the image board, we hold down the “n” key on our keyboard, hold our mouse pointer over the tip of the board nose on the image and left click our mouse. The dialogue box for aligning the image board. Remember we can always change the board size at any time while we are designing in AKU.Ĭlick, we choose the directory where we saved our board plan and profile image. We'll select the size that is closest to the final size of board, about 8'. The board size template that is chosen will depend on what size board is required. There is also a reference card in the categories.Ĭlick in the drop down box and click OK. Click on the "Help" menu option and then "Help" again. There are also some tutorials to get you started as well. ![]() You should end up with a screen like this.īefore we get back into the tutorial, I wanted to mention that AKU does have a help option that has some good reference information. ![]() This may take a few minutes so please be patient. I had to flip the board 90 degrees to line up the nose and tail with the board direction in AKU. This will be the board image which we will base our design on. I've saved the board image to my laptop and then edited it in Microsoft Paint to make sure that the nose of the board is pointing to the right hand side of the computer screen. For the purposes of this tutorial I've used Google images and found an image of a rounded pin tail that I like. We could photograph a board or find a picture on the Web. This design key will also allow you to make adjustments to the top outline in the Outline tab, as opposed to working from the bottom outline of the board.Designing Hollow Wooden Surfboard Templatesįirstly, we need to find a picture of a board plan shape and profile (rocker) that we like. Show Rocker Upside Down: Flip your design upside down for an alternative design perspective This feature will also remain active in the Top/Bottom tabs: Nose Right: Flip your design the other way for an additional design perspective Point Movement Size: Change the size of the adjust increments for fine tuning critical parts of your designĠ.1 mm = Ultra Fine 1.0 mm = Medium 1.0 Pixel = Heavy movement Nose Right Spot Check: Clear all board information for a clear view of your design. Left/ Right Arrows: Pan an entire design left or right with these arrows Spot Check You may also use the arrow keys on your keyboard. These functions can also be controlled from the Dimensions tab in the toolbar.Īrrow Key Controls: Control the position of your design using these keys. ![]() *In the Change Dimensions box, keys can be punched in using a. The corresponding guide at the top allows the shaper to take incremental measurements of a designįt - cm - mm - ft (decimal) - Ft / mm Keysįt-cm-mm-ft (decimal)-ft/mm Keys: These keys are used to toggle between different units of measurements How to use the N Rocker - T Rocker Tool 1:1 Ratio Toolġ:1 Ratio Tool: Used an alternative, zoomed out design perspective. *Use the Up and Down arrow keys to control the movement of the rocker N Rocker: Move the entire Nose rocker up or down using in the Top/Bottom tab T Rocker: Move the entire Tail rocker up or down using this key in the Top/Bottom tab To manually enter points, use the Guide Points tab in the tool bar. To add points, use the Add Guide key in the tool bar. Or to make marks along an outline to plot out a new shape. Undo - Redo Keys: Use the back and forward keys to undo a change or redo a change Add GuideĪdd Guide: Guide points are added to use a reference point from an existing shape. Points can be added in the Outline, Slices, Top, and Bottom tabs *Tip: Zoom In & Place control points close together to create wings, beak noses, and channels. Points must be added at the bottom outline of the design. Zoom Fit: Revert back to full view from the zoom position Add PointĪdd Point: Add additional control points using this key. Zoom Box: Draw a square around the area you want to zoom to work in a closer proximity Startup Guide on How to use AkuShaper toolbar keys Zoom Box ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |